The model 210CR, 410CR, 610CR, and 720CR Cycle Racks hitch to your frame-mounted 2"x2" class III or better receiver hitch (use a class IV or V receiver hitch for model 610CR and the model 720CR 2-place Cycle Rack). The Cycle Rack tilts for easy loading with no heavy lifting or hazardous ramps. It has an extender to reduce the incline on taller vehicles and it also prevents the channel from leveling before the rear wheel is on board. The slam latch locks the channel in the leveled position while you attach your tie-down straps to the horizontal bars for safe transporting of your bike(s). The motion reducer bolt, when tight, reduces the side-to-side motion in the receiver hitch and also discourages theft of the rack.

Attach the Cycle Rack to your host vehicle by first removing the 5/8" receiver-hitch pin. Then insert the hitch bar into the receiver hitch of your vehicle until the pinholes in both units are aligned. Reinsert the hitch pin and its safety securing R clip. Tighten the bolt on the side of the hitch bar to reduce any movement in the hitch.

The channel extender slides out from under the Cycle Rack channel 16 inches. This feature allows the motorcycle's rear wheel to be on board before the cycle reaches the balance point and also reduces the angle of incline. The extender is held in place by a 5/16" pin connected by a small chain. After pulling out the extender, go to the opposite end and release the slam latch while holding onto the Cycle Rack so it does not tilt too quickly. Slowly allow the channel to tilt until the end of the channel extender touches the ground. Be sure the latch is in its ready-to-lock position. You are now ready to load your bike.

Push your bike up onto the rack until the front wheel is all the way forward in the wheel hoop and the channel rocks forward to engage the slam latch. Hook your tie-down straps from the handle bars to the tie-down bar, pull the tie-down straps tight while rocking the bike side to side until the front spring shocks are compressed. Secure another strap to the rear wheel, going through the wheel and around the rack. Slide the extender in and reinsert the 5/16" pin. You are now ready to go!

RETURN POLICY
Refunds are made only if product is found to be defective and not repairable as stated in Warranty. You must call 303-450-2881 for a return authorization number (RA#). If ATV SOLUTIONS agrees to the return of a non defective product, and the unit was purchased from ATV SOLUTIONS, refund will be the original cost of the unit, less any shipping & handling, and a 20% restocking fee will be charged. ATV SOLUTIONS will refuse delivery and no refund will be issued for
   (1) unauthorized returns that do not have RA #,
   (2) unauthorized freight collect returns, and/or
   (3) any product returned to us unpackaged or not properly packaged.

Refunds will be by company check within 45 days of receipt of returned merchandise that has not been abused, altered or misused. ATV SOLUTIONS, Inc., reserves the right to replace the defective product with a new unit. Exchanges: the customer will be responsible for paying the 1st outbound freight and the return freight; ATV SOLUTIONS will pay for the 2nd outbound freight.

Do not place flammable or nonflammable objects such as luggage, cloth, plastic tarps, wood, gas cans, etc., in front of, behind, or near exhaust of vehicle. The heat from the exhaust could ignite items in its path!

WARRANTY

Mesa Verde Manufacturing, Inc., warrants all parts of this Tilt-A-Rack® Cycle product to be free from defects in material and workmanship within one (1) year from the date purchased. Within this period, Mesa Verde Manufacturing, Inc., shall correct any defect by repairing or replacing defective parts of the equipment. Mesa Verde Manufacturing, Inc., shall not be obligated to refund, repair, or replace equipment that has been repaired by others, abused, altered, or misused. We further state that we shall not be held liable for any losses due to neglectful operation or misuse on the part of the purchaser, nor are we responsible for damage caused by inadequate hitch receivers or host vehicles. No other warranties are expressed or implied. Upon the expiration of such warranty, all liability shall terminate.

NOTE: Paint finish will scratch and chip under normal use and therefore carries no warranty. Lights and wiring carry no warranty.

RETURN POLICY
Refunds are made only if product is found to be defective and not repairable as stated in Warranty. You must call 303-450-2881 for a return authorization number (RA#). If ATV SOLUTIONS agrees to the return of a non defective product, and the unit was purchased from ATV SOLUTIONS, refund will be the original cost of the unit, less any shipping & handling, and a 20% restocking fee will be charged. Mesa Verde Mfg. will refuse delivery and no refund will be issued for
   (1) unauthorized returns that do not have an RA#,
   (2) unauthorized freight collect returns, and/or
   (3) any product returned to us unpackaged or not properly packaged.

Refunds will be by company check within 45 days of receipt of returned merchandise that has not been abused, altered or misused. Mesa Verde Mfg., Inc., reserves the right to replace the defective product with a new unit. Exchanges: the customer will be responsible for paying the 1st outbound freight and the return freight; Mesa Verde Mfg. will pay for the 2nd outbound freight.

Motorcycle Carriers by MotorCycleCarrier.net

***WARRANTY***

Motorcycle Carriers
by MotorCycleCarrier.net

WARRANTY